Difference between revisions of "Matrix - Temperature and Humidity Sensor"
From FriendlyELEC WiKi
(→Introduction) |
|||
| Line 3: | Line 3: | ||
==Introduction== | ==Introduction== | ||
[[File:TemperatureAndHumiditySensor01.png|thumb|Temperature and Humidity Sensor]] | [[File:TemperatureAndHumiditySensor01.png|thumb|Temperature and Humidity Sensor]] | ||
| − | This module utilizes the DHT11 temperature and humidity sensor. The DHT11 sensor's relative humidity range is 20%-80% ±5% and its temperature range is 0℃-50℃ ±2℃. DHT11 uses a single bus communication which needs only one data line. DATA is used for communication and synchronization between the microprocessor and DHT11. Its data format consists of the 8bit humidity integer data and 8bit the Humidity decimal data, and 8 bit temperature integer data and 8bit fractional temperature data and 8 bit parity bit. Its application of a dedicated digital modules collection technology and the temperature and humidity sensing technology, to ensure that the product has high reliability, excellent long-term stability, low cost and long distance (up to 20 meters) signal transmission. We simplified the DHT11's 4-pin to 3-pin. | + | This module utilizes the DHT11 temperature and humidity sensor. The DHT11 sensor's relative humidity range is 20%-80% ±5% and its temperature range is 0℃-50℃ ±2℃. DHT11 uses a single bus communication which needs only one data line. Its DATA line is used for communication and synchronization between the microprocessor and DHT11. Its data format consists of the 8bit humidity integer data and 8bit the Humidity decimal data, and 8 bit temperature integer data and 8bit fractional temperature data and 8 bit parity bit. Its application of a dedicated digital modules collection technology and the temperature and humidity sensing technology, to ensure that the product has high reliability, excellent long-term stability, low cost and long distance (up to 20 meters) signal transmission. We simplified the DHT11's 4-pin to 3-pin. |
| − | == | + | ==Features== |
| − | * | + | * Humidity range: 20-80%RH, temperature range: 0~50℃ |
| − | * | + | * Humidity accuracy:±5%RH, temperature accuracy: ±2℃ |
* 一线协议 | * 一线协议 | ||
* 2.54mm排针接口，接线方便，通用性强 | * 2.54mm排针接口，接线方便，通用性强 | ||
Revision as of 08:46, 5 August 2015
1 Introduction
This module utilizes the DHT11 temperature and humidity sensor. The DHT11 sensor's relative humidity range is 20%-80% ±5% and its temperature range is 0℃-50℃ ±2℃. DHT11 uses a single bus communication which needs only one data line. Its DATA line is used for communication and synchronization between the microprocessor and DHT11. Its data format consists of the 8bit humidity integer data and 8bit the Humidity decimal data, and 8 bit temperature integer data and 8bit fractional temperature data and 8 bit parity bit. Its application of a dedicated digital modules collection technology and the temperature and humidity sensing technology, to ensure that the product has high reliability, excellent long-term stability, low cost and long distance (up to 20 meters) signal transmission. We simplified the DHT11's 4-pin to 3-pin.
2 Features
- Humidity range: 20-80%RH, temperature range: 0~50℃
- Humidity accuracy:±5%RH, temperature accuracy: ±2℃
- 一线协议
- 2.54mm排针接口，接线方便，通用性强
3 使用方法
3.1 连接
- 连接到Tiny4412 SDK (1506)
- GND针脚: 接地
- VCC: 接5V
- S针脚：接GPIO PIN1, 必须使用中断引脚，可用引脚(1、2、3、4、9、10)
3.2 Linux下的C示例
#include <stdio.h> #include <stdlib.h> #include "libfahw.h" void parseCmd(int argc, char **argv, int *pin) { int num = atoi(argv[1]); switch(num) { case 1: *pin = TINY4412_GPIO_PIN1; break; case 2: *pin = TINY4412_GPIO_PIN2; break; case 3: *pin = TINY4412_GPIO_PIN3; break; case 4: *pin = TINY4412_GPIO_PIN4; break; case 9: *pin = TINY4412_GPIO_PIN9; break; case 10: *pin = TINY4412_GPIO_PIN10; break; default: printf("Unsupported pin TINY4412_GPIO_PIN%d\n", num); num = 1; *pin = TINY4412_GPIO_PIN1; } printf("Using pin TINY4412_GPIO_PIN%d\n", num); } int main(int argc, char ** argv) { int ret = -1; int dhtTemp = 0; int dhtHdty = 0; int devFD = -1; int pin = TINY4412_GPIO_PIN1; if (argc == 2) { parseCmd(argc, argv, &pin); } else { printf("Using default pin TINY4412_GPIO_PIN1\n"); } if ((devFD = dht11Init(pin)) == -1) { printf("Fail to init dht11\n"); return -1; } if ((ret = dht11Read(DHT_HUMIDITY, &dhtHdty)) != -1) { printf("Get humidity : %d\n", dhtHdty); } else { printf("Faided to get humidity\n"); } if ((ret = dht11Read(DHT_TEMP, &dhtTemp)) != -1) { printf("Get temperature : %d\n", dhtTemp); } else { printf("Faided to get temperature\n"); } dht11DeInit(devFD); return ret; }
3.3 编译并运行示例
git clone http://github.com/friendlyarm/fa-hardware.git cd fa-hardware cd demo cd matrix-temperature_and_humidity_sensor make
将编译生成的dht11通过ftp上传到开发板上运行即可测试。
