Difference between revisions of "Matrix - T-Cobbler40 for Pi/zh"
From FriendlyELEC WiKi
(→介绍) |
(→特性) |
||
| Line 6: | Line 6: | ||
==特性== | ==特性== | ||
| − | * | + | * 1个2.54mm 40Pin排线插座 |
| − | * | + | * 2个2.54mm 20Pin排针 |
| − | + | ||
* PCB尺寸（mm）：40x64 | * PCB尺寸（mm）：40x64 | ||
[[File:Matrix - T-Cobbler40 for Pi_PCB.png | frameless|400px|Matrix - T-Cobbler40 for Pi_PCB.PCB]] | [[File:Matrix - T-Cobbler40 for Pi_PCB.png | frameless|400px|Matrix - T-Cobbler40 for Pi_PCB.PCB]] | ||
| Line 58: | Line 57: | ||
|39 || GND || ||40 || UART3_RX/SPI1_CLK/GPIOA14 || 14 | |39 || GND || ||40 || UART3_RX/SPI1_CLK/GPIOA14 || 14 | ||
|} | |} | ||
| − | |||
| − | |||
==硬件连接== | ==硬件连接== | ||
Revision as of 05:25, 16 November 2016
1 介绍
- 模块Matrix - T-Cobbler40 for Pi是一个方便、实用的专为创客DIY打造的40 Pin IO接口扩展模块，模块使用40 Pin排线与Pi连接，2.54mm间距的排针可直接插接在面包板上，并在面包板上搭建电路。
- 相比于使用杜邦线杂乱的连接面包板，使用T-Cobbler40 for Pi模块能更高效、快速、美观的搭建好电路，并能使用所有的Pi的40 Pin接口。
2 特性
- 1个2.54mm 40Pin排线插座
- 2个2.54mm 20Pin排针
- PCB尺寸（mm）：40x64
- 引脚说明:
- 40 Pin排针引脚定义：
| Pin# | Name | Linux gpio | Pin# | Name | Linux gpio |
| 1 | SYS_3.3V | 2 | VDD_5V | ||
| 3 | I2C0_SDA | 4 | VDD_5V | ||
| 5 | I2C0_SCL | 6 | GND | ||
| 7 | GPIOG11 | 203 | 8 | UART1_TX/GPIOG6 | 198 |
| 9 | GND | 10 | UART1_RX/GPIOG7 | 199 | |
| 11 | UART2_TX/GPIOA0 | 0 | 12 | PWM1/GPIOA6 | 6 |
| 13 | UART2_RTS/GPIOA2 | 2 | 14 | GND | |
| 15 | UART2_CTS/GPIOA3 | 3 | 16 | UART1_RTS/GPIOG8 | 200 |
| 17 | SYS_3.3V | 18 | UART1_CTS/GPIOG9 | 201 | |
| 19 | SPI0_MOSI/GPIOC0 | 64 | 20 | GND | |
| 21 | SPI0_MISO/GPIOC1 | 65 | 22 | UART2_RX/GPIOA1 | 1 |
| 23 | SPI0_CLK/GPIOC2 | 93 | 24 | SPI0_CS/GPIOC3 | 67 |
| 25 | GND | 26 | SPDIF-OUT/GPIOA17 | 17 | |
| 27 | I2C1_SDA/GPIOA19 | 19 | 28 | I2C1_SCL/GPIOA18 | 18 |
| 29 | GPIOA20 | 20 | 30 | GND | |
| 31 | GPIOA21 | 21 | 32 | GPIOA7 | 7 |
| 33 | GPIOA8 | 8 | 34 | GND | |
| 35 | UART3_CTS/SPI1_MISO/GPIOA16 | 16 | 36 | UART3_TX/SPI1_CS/GPIOA13 | 13 |
| 37 | GPIOA9 | 9 | 38 | UART3_RTS/SPI1_MOSI/GPIOA15 | 15 |
| 39 | GND | 40 | UART3_RX/SPI1_CLK/GPIOA14 | 14 |
3 硬件连接
3.1 连接NanoPi M1
参考下图连接模块：
