Difference between revisions of "Template:NetworkPerformanceTest"
From FriendlyELEC WiKi
| Line 1: | Line 1: | ||
| − | == | + | ==Test Network Performance== |
| − | * | + | * In Friendlycore we can use the iperf utility to test network performance. Make sure your board is connected properly and the hardware works before start testing |
[[File:network cable.jpg|frameless|400px]]<br> | [[File:network cable.jpg|frameless|400px]]<br> | ||
| − | * | + | * To avoid interference from unexpected sources use an independent IP section and test with a PC host. |
| − | === | + | ===Setup Network=== |
| − | * | + | * When you test Ethernet please disable WiFi. You can disable WiFi by running the following commands. |
<syntaxhighlight lang="bash"> | <syntaxhighlight lang="bash"> | ||
ifconfig wlan0 down | ifconfig wlan0 down | ||
| Line 10: | Line 10: | ||
</syntaxhighlight> | </syntaxhighlight> | ||
[[File:NanoPi_R1S-H3_ifconfig.jpg|frameless|650px]]<br /> | [[File:NanoPi_R1S-H3_ifconfig.jpg|frameless|650px]]<br /> | ||
| − | * | + | *When you test WiFi please disconnect or disable Ethernet. You can disable Ethernet by running the following commands. |
<syntaxhighlight lang="bash"> | <syntaxhighlight lang="bash"> | ||
ifconfig eth0 down | ifconfig eth0 down | ||
Revision as of 11:45, 25 December 2019
1 Test Network Performance
- In Friendlycore we can use the iperf utility to test network performance. Make sure your board is connected properly and the hardware works before start testing
- To avoid interference from unexpected sources use an independent IP section and test with a PC host.
1.1 Setup Network
- When you test Ethernet please disable WiFi. You can disable WiFi by running the following commands.
ifconfig wlan0 down ifconfig
- When you test WiFi please disconnect or disable Ethernet. You can disable Ethernet by running the following commands.
ifconfig eth0 down ifconfig
1.2 测试开发板发送性能
PC机做server，开发板做client，测试开发板向PC机发送数据的性能。
- 1、使用以下命令查看PC机的IP地址，例如本机的IP地址为192.168.10.100
ifconfig- 2、在PC机终端使用以下命令运行iperf软件，并设置PC机为server
iperf -s- 3、在开发板的调试终端执行以下命令，运行iperf软件，并设置开发板为client，开始测试，请注意IP地址需改成你的PC机实际的IP地址
iperf -c 192.168.10.100 -t 60 -i 1
以NanoPi R1S-H3为例，实际发送性能测试如下图所示：
1.3 测试开发板接收性能
开发板做server，PC机做client，测试开发板接收PC机数据的性能。
- 1、使用以下命令查看开发板的IP地址，例如本开发板的IP地址为192.168.10.102
ifconfig- 2、在开发板终端使用以下命令运行iperf软件，并设置开发板为server
iperf -s- 3、在PC机的终端执行以下命令，运行iperf软件，并设置PC机为client，开始测试，请注意IP地址需改成你的开发板实际的IP地址
iperf -c 192.168.10.102 -t 60 -i 1
以NanoPi R1S-H3为例，实际接收性能测试如下图所示：
