Difference between revisions of "Matrix - Temperature Sensor"

Revision as of 07:21, 18 September 2015

查看中文

1 Introduction

Temperature Sensor

• The matrix-temperature_sensor module is used to measure temperature.
• We utilitze the DS18B20 chip with the To-92 package in this module. Its unique 1-wire interface requires only 1 port pin for reading/writing. Power for reading, writing, and performing temperature conversions can be derived from the data line itself with no need for an external power source. The DS18B20 can be powered from its data line. Each DS18B20 is assigned a unique ID.
• Its temperature range is -55 degree Celsius to +125 degree Celsius. The thermometer resolution is programmable from 9 to 12 bits. When the measured temperature is between -10 degree Celsius to +85 degree Celsius the accuracy can be at 0.5 degree. Among all three DS18B20 pins V is power, G is ground and S is data.

2 Features

• -55 degree Celsius to +125 degree Celsius
• One wire interface for communication
• Tiny, easy to be deployed in various situations
• 2.54mm spacing pin
• PCB dimension(mm): 8 X 24

• Pin Description:

3 工作原理

DS18B20低温度系数晶振的振荡频率受温度影响很小，用于产生固定频率的脉冲信号送给计数器1。高温度系数晶振随温度变化其振荡率明显改变，所产生的信号作为计数器2的脉冲输入。计数器1和温度寄存器被预置在-55℃所对应的一个基数值。计数器1对低温度系数晶振产生的脉冲信号进行减法计数，当计数器1的预置值减到0时，温度寄存器的值将加1，计数器1的预置将重新被装入，计数器1重新开始对低温度系数晶振产生的脉冲信号进行计数，如此循环直到计数器2计数到0时，停止温度寄存器值的累加，此时温度寄存器中的数值即为所测温度。

4 Download Matrix Source Code

All the matrix modules' code samples are open source. They are maintained in a git hub - git://github.com/friendlyarm/matrix.git
Each branch in this hub contains the matrix modules' code samples for a board that the matrix modules can work with.

• The nanopi branch contains the matrix modules' code samples for the NanoPi
• The tiny4412 branch contains the matrix modules' code samples for the Tiny4412
• The raspberrypi branch contains the matrix modules' code samples for the RaspberryPi

Please follow the steps below to get the source code:
Install the git utility on a PC running Ubuntu14.04

$ sudo apt-get install git

Clone the matrix code hub

$ git clone git://github.com/friendlyarm/matrix.git

If this is successful a "matrix" directory will be generated, which will contain all the matrix modules' code samples.

5 Connect to NanoPi

5.1 Preparations

Please install a Debian on a NanoPi and an appropriate cross compiler on a PC. Please refer to wiki: NanoPi
Compile a NanoPi kernel. Note: please use the kernel's source code from the nanopi-v4.1.y-matrix branch

$ git clone https://github.com/friendlyarm/linux-4.x.y.git
$ cd linux-4.x.y
$ git checkout nanopi-v4.1.y-matrix
$ make nanopi_defconfig
$ touch .scmversion
$ make

5.2 Hardware Connection

Please refer to the following connection diagram to connect the Matrix-Temperature_Sensor module to the NanoPi

Connection Details:

5.3 Compile Test Program

Please login the matrix hub and enter the nanopi branch

$ cd matrix
$ git checkout nanopi

Compile the matrix code

$ make CROSS_COMPILE=arm-linux- clean
$ make CROSS_COMPILE=arm-linux-
$ make CROSS_COMPILE=arm-linux- install

Note: please make sure to install the cross compiler "arm-linux-gcc-4.4.3" on your PC, which is used to compile files for the NanoPi-Debian.
Generated library files are under the "install/lib" directory. Applications are under the "install/usr/bin" directory. The test program for the "Matrix-Temperature_Sensor" module is "matrix-temperature_sensor".

5.4 Run Test Program

Please copy the library files and test program to the NanoPi

$ cp install/usr/bin/* nanopi_rootfs/usr/bin/
$ cp install/lib/* nanopi_rootfs/lib/ -d

Power on the NanoPi and run the following command in Debian's terminal
Note: this module is not plug and play therefore before running the module please make sure it is connected to a NanoPi.

$ matrix-temperature_sensor

5.5 Code Sample

int main(int argc, char ** argv)
{
    int devFD = -1;
    int pin = GPIO_PIN1;
    char *temperature = (char *) malloc(32);
    memset(temperature, 0, 32);
 
    if (argc == 2) {
        parseCmd(argc, argv, &pin);
    } else {
        printf("Using default pin GPIO_PIN1\n");
    }
 
    if ((devFD = ds18b20Init(pin)) == -1) {
        printf("Fail to init ds18b20\n");
        return -1;
    }
    if (ds18b20Read(temperature) > 0) {
        printf("Temperature = %s\n", temperature);
    } else {
        printf("Fail to get temperature\n");		
    }
    free(temperature);
    ds18b20DeInit(devFD);
    return 0;
}

6 Connect to Tiny4412

6.1 Preparations

Please refer to the Tiny4412's user's manual to install a UbuntuCore on the Tiny4412 and install an appropriate cross compiler on a PC.
Note: only the Tiny4412SDK-1506 carrier board can work with this module.

6.2 Hardware Connection

Please refer to the following diagram to connect the Matrix-Temperature_Sensor to the Tiny4412

Connection Details:

6.3 Compile Test Program

Please login the Matrix hub and enter the matrix-tiny4412 branch

$ cd matrix
$ git checkout tiny4412

Compile the matrix code

$ make CROSS_COMPILE=arm-linux-gnueabihf- clean
$ make CROSS_COMPILE=arm-linux-gnueabihf-
$ make CROSS_COMPILE=arm-linux-gnueabihf- install

Note: please make sure to install the cross compiler "arm-linux-gnueabihf-gcc-4.7.3" on your PC, which is used to compile files for the Tiny4412-UbuntuCore.
Generated library files are under the "install/lib" directory. Applications are under the "install/usr/bin" directory. The test program for the "Matrix-Temperature_Sensor" module is "matrix-temperature_sensor".

6.4 Run Test Program

Please copy the library files and test program to the Tiny4412

$ cp install/usr/bin/* tiny4412_rootfs/usr/bin/
$ cp install/lib/* tiny4412_rootfs/lib/ -d

Power on the Tiny4412 and run the following command in UbuntuCore's terminal
Note: this module is not plug and play therefore before running the module please make sure it is connected to a Tiny4412.

$ matrix-temperature_sensor

6.5 Code Sample

int main(int argc, char ** argv)
{
    int devFD = -1;
    int pin = GPIO_PIN1;
    char *temperature = (char *) malloc(32);
    memset(temperature, 0, 32);
 
    if (argc == 2) {
        parseCmd(argc, argv, &pin);
    } else {
        printf("Using default pin GPIO_PIN1\n");
    }
 
    if ((devFD = ds18b20Init(pin)) == -1) {
        printf("Fail to init ds18b20\n");
        return -1;
    }
    if (ds18b20Read(temperature) > 0) {
        printf("Temperature = %s\n", temperature);
    } else {
        printf("Fail to get temperature\n");		
    }
    free(temperature);
    ds18b20DeInit(devFD);
    return 0;
}

7 与RaspberryPi连接使用

8 与Arduino连接使用

9 相关资料

DS18B20.pdf