Difference between revisions of "Mini Shield for NanoPi Duo"

Revision as of 05:54, 16 August 2017

查看中文

1 Introduction

Mini Shield for NanoPi Duo 侧面

Mini Shield for NanoPi Duo 正面

Mini Shield for NanoPi Duo 底面

• The Mini Shield for NanoPi Duo is a dedicated carrier board for the NanoPi Duo. It extends Duo's Ethernet, serial port, audio, USB and etc.
• The mini shield has an onboard JMS567 USB to SATA IC and an mSATA interface.
• The mini shield has an onboard FE1.1s which extends four USB Host ports.
• It has a serial port and Ethernet port.
• It has an onboard microphone and a 3.5mm audio jack.
• The mini shield has a 2 x9 Pin header which extends NanoPi Duo's IO pins.
• There is a 6-pin SPI header on the reverse side.
• This shield's dimension and mounting holes' positions are exactly the same as those of a Raspberry Pi therefore it can be well fitted into a Raspberry Pi's case.

2 Hardware Spec

• its dimension is the same as that of a Raspberry Pi and it can fit into a Pi's case
• 4个USB Host接口
• 扩展的调试串口和网络接口
• 音频输入、输出接口
• 2x9 Pin GPIO排针
• 6Pin SPI 排针
• PCB尺寸（mm）：85x56

2.1 接口说明

Mini Shield for NanoPi Duo接口布局

Mini Shield for NanoPi Duo接口如右图所示，接口引脚丝印都在板子背面做了详细标注。

• Mini Shield for NanoPi Duo接口引脚定义

Number#	Name		Number#	Name
1	VDD_5V		1	DEBUG_RX(UART_RXD0)/GPIOA5/PWM0
2	VDD_5V		2	DEBUG_TX(UART_TXD0)/GPIOA4
3	SYS_3.3V		3	GND
4	GND		4	I2C0_SCL/GPIOA11
5	GPIOL11/IR-RX		5	I2C0_SDA/GPIOA12
6	GPIOG11		6	UART3_TX/SPI1_CS/GPIOA13
7	USB-DM3		7	UART3_RX/SPI1_CLK/GPIOA14
8	USB-DP3		8	UART3_CTS/SPI1_MISO/GPIOA16
9	USB-DM2		9	UART3_RTS/SPI1_MOSI/GPIOA15
10	USB-DP2		10	UART1_RX/GPIOG7
11	EPHY-RXN		11	UART1_TX/GPIOG6
12	EPHY-RXP		12	CVBS
13	EPHY-TXN		13	LINEOUT_L
14	EPHY-TXP		14	LINEOUT_R
15	EPHY-LED-LINK		15	MIC_P
16	EPHY-LED-SPD		16	MIC_N

• 2x9 Pin排针引脚定义

Number#	Name	Number#	Name
1	SYS_3.3V	2	VDD_5V
3	I2C0_SDA / GPIOA12	4	VDD_5V
5	I2C0_SCL / GPIOA11	6	GND
7	GPIOG11	8	UART1_TX / GPIOG6
9	GND	10	UART1_RX / GPIOG7
11	SPI1_MOSI/GPIOA15	12	GPIOL11
13	SPI1_MISO/GPIOA16	14	GND
15	SPI1_CLK/GPIOA14	16	SPI1_CS/GPIOA13
17	SYS_3.3V	18	NC

• 6 Pin SPI排针引脚定义

Number#	Name
1	GND
2	SYS_3.3V
3	SPI1_CS/GPIOA13
4	SPI1_CLK/GPIOA14
5	SPI1_MOSI/GPIOA15
6	SPI1_MISO/GPIOA16

3 硬件连接

NanoPi Duo可直接装配在Mini Shield for NanoPi Duo底板上，装配时注意NanoPi Duo的方向，参考下图连接模块：

并可装配在树莓派外壳中，参考下图装配：

4 软件使用

4.1 1、mSATA接口使用

插入半高的mSATA接口SSD，启动系统后，可使用如下命令查看SSD：

fdisk -l

运行效果如下：

4.2 2、音频输入与输出

1、可使用以下命令录音：

xxxxx

运行效果如下：
2、可使用以下命令播放音频文件：

xxxxx

运行效果如下：

5 相关资料

• [Schematic](Schematic - Mini Shield for NanoPi Duo.pdf)
• [Dimension](Dimension - Mini Shield for NanoPi Duo_PCB（dxf）)