Smart4418 SDK

From FriendlyELEC WiKi
Revision as of 13:44, 2 August 2016 by Yftan (Talk | contribs) (资源特性)

Jump to: navigation, search

查看中文


1 Introduction

Overview
Front
  • The Smart4418 SDK carrier board V1606 has various interfaces and ports like HDMI port, USB host, SD card slot, SB9 serial port, RJ-45 Ethernet port, 3.5mm audio jack, SATA interface, MiniPCIe, MicroSIM etc with support for 3G/4G Bluetooth & WiFi.In addition it has hardware resources like buzzer, user keys, RTC battery, microphone and etc for users to evaluate its performance and features. FriendlyARM designed it for sake of industrial applications by putting all commonly used interfaces and ports on one side with mounting holes for easy deployment.
  • To make this carrier board applicable in various applications compared to our existing carrier boards we add more interfaces and ports such as DVP camera interface, SPI, GPIO, I2C, AP6212 WiFi & Bluetooth module, porcelain antenna, RTC seat and etc.

2 资源特性

Features
SDK Carrier Board Model Smart4418SDK 1606
Dimension 189.8 x 118.2(mm)
Applicable CPU Board Smart4418
WiFi/Bluetooth Onboard WiFi & Bluetooth
MiniPCIe Interface For 4G modules, data service only, speech service not applicable
SIM Card Slot Pop-up MicroSIM card slot
Antenna Onboard porcelain antenna
DVP Camera Interface 24pin, 0.5mm pitch FPC seat
DVP Camera interface, ITU-R BT 601/656 8-bit
HDMI Interface 1 x HDMI A Type, HDMI 1.4a (Smart4418)
1080p30 video output
RS232 Serial Interface 2 x 3-wire serial port (UART0 and 3), DB9 male connector
USB Host 2 x USB A
brought out from USB 2.0 hub, (USB 1.1 compatible)
USB Slave 1 x Micro USB, data communication only
Audio Interface Internal Audio
supports audio recording and play
3.5mm audio jack and MIC
onboard Microphone
Ethernet Internal 1000/100/10M Ethernet
User Key PWRKEY (power key)
RST (reset)
K1/K2/K3 programmable keys
LED 2 x GPIO LED (On Smart4418 CPU board)
RTC Onboard RTC battery(CR1220)
Buzzer 1 x PWM buzzer
SPI Interface CON3: 26pin ,2.54mm pitch double row pin-header
GPIO Header GPIOC9, GPIOC10, GPIOC11 and GPIOC12
SD Card Slot Pop-up SD card slot
I2C Interface I2C0
UART Serial Interface UART2
SATA Onboard SATA interface
SATA Power Onboard SATA power interface
LCD Interface LCD Interface(45pin, 0.5mm pitch FPC seat)
Supports FriendlyARM one wire technology
back-light adjustable
Supports LCDs with capacitive touch
Supports RGB888
Supports full color TFT CD
LCD Mounting Holes Applicable for X710 LCD
LVDS Interface 2pin, 2.0mm pitch
GPIO Pin-header 30pin 2.0mm pitch double-row pin-header including 1x UART, 1x I2C, 1 x SPI, 1 x SDIO and 11 x GPIO
Other Resources 1 x EEPROM, 1 x 3-Axis Digital Accelerometer
Power DC 9V~24V/2A. When you connect a SATA hard disk or LVDS LCD to it a 12V/3A power adapter is required

3 接口描述和尺寸

3.1 接口描述

  • LVDS接口
Pin# Name Pin# Name
1 SYS_3.3V 2 SYS_3.3V
3 GPIOC16 4 GPIOB18
5 DGND 6 DGND
7 LVDS_D0- 8 LVDS_D0+
9 LVDS_D1- 10 LVDS_D1+
11 LVDS_D2- 12 LVDS_D2+
13 DGND 14 DGND
15 LVDS_CLK- 16 LVDS_CLK+
17 LVDS_D3- 18 LVDS_D3+
19 I2C2_SCL 20 I2C2_SDA
  • DVP摄像头接口
Pin# Name
1, 2 SYS_3.3V
7,9,13,15,24 DGND
3 I2C0_SCL
4 I2C0_SDA
5 GPIOB14
6 GPIOB16
8,10 NC
11 VSYNC
12 HREF
14 PCLK
16-23 Data bit7-0
  • LCD接口
Pin# Name Description
1, 2 VDD_5V 5V输出, 可以给LCD模组供电
11,20,29, 37,38,39,40, 45 DGND 参考地, 0电位
3-10 Blue LSB to MSB RGB的蓝色信号
12-19 Green LSB to MSB RGB的绿色信号
21-28 Red LSB to MSB RGB的红色信号
30 GPIOB25 普通GPIO, 用户可控制
31 GPIOC15 一线协议信号, 以实现LCD型号识别,

背光控制和电阻触摸的功能. 系统已占用, 用户不可重新设置.

32 XnRSTOUT Form CPU 系统复位时向外输出低电平
33 VDEN 指示RGB信号有效的信号
34 VSYNC 场信号
35 HSYNC 行信号
36 LCDCLK LCD频率, Pixel frequency
41 I2C2_SCL I2C2的时钟信号, 用来传输电容屏触摸数据
42 I2C2_SDA I2C2的数据信号, 用来传输电容屏触摸数据
43 GPIOC16 电容触摸中断信号, 配合I2C2使用
44 NC 没有任何连接
  • SATA接口
  • 标准7Pin数据接口, 大4Pin电源接口
SATA-01.png


  • 电源接口
  • DC电源座子, 适合DC5.5*2.1mm电源插头, 9V~24V宽电压输入, 因为SATA电源和LVDS背光电源跟输入电源直接连通, 所以当使用SATA或LVDS背光时, 必须12V/3A供电
DC-005.png
  • 2.54mm间距, 2510-4P针座. Pin1~Pin4定义: VDD_12V, DGND, DGND, 12V_IN
    其中12V_IN直接连到DC电源座子, VDD_12V是5V_IN经过开关S1后连接到板子的12V电源网络
CON5.png

3.2 机械尺寸

Smart4418SDK-1606-Dimensions

详细尺寸:dxf文件

4 资源链接

SDK硬件设计文件
PCB源文件, 使用Allegro 16.5或以上版本
PCB dxf文件
原理图源文件, 使用OrCAD 16.5或以上版本
原理图pdf文件
Smart4418核心板软件和硬件详细介绍
Smart4418原理图pdf