Difference between revisions of "Power Dock for NanoPi NEO"

From FriendlyELEC WiKi
Jump to: navigation, search
(Created page with "查看中文")
 
 
(3 intermediate revisions by the same user not shown)
Line 1: Line 1:
 
[[Power Dock for NanoPi NEO/zh|查看中文]]
 
[[Power Dock for NanoPi NEO/zh|查看中文]]
 +
 +
==Introduction==
 +
[[File:Power Dock for NanoPi NEO .png|thumb|Power Dock for NanoPi NEO]]
 +
* The Power Dock for NanoPi NEO is a power conversion board.
 +
* It uses TI's TPS54331 device with wide voltage range.TPS54331 integrates a low RDS(on) high-side MOSFET.
 +
* Its slow-start feature limits inrush currents. Its overvoltage transient protection circuit limits voltage overshoots during startup and transient conditions.
 +
* Its side A has double-layer tall female connectors which allow a NEO to be stacked on the board. Its side B populates NEO's GPIO pins.
 +
 +
==Hardware Spec==
 +
* Input Voltage: 12V
 +
* Output: 5V/2A
 +
* Switching Frequency: 570KHz
 +
* Shutdown Quiescent Current: 1uA
 +
* Under Voltage Lockout
 +
* Overvoltage Protection
 +
* Slow-Start
 +
<!--- 小康建议去掉，这两项需要实际测量
 +
* 负载调整率：±1%
 +
* 电压调整率：±0.5%
 +
--->
 +
* PCB dimension(mm): 40 x 88
 +
[[File:Power Dock for NanoPi NEO.png | frameless|800px|Power Dock for NanoPi NEO_PCB]]
 +
 +
* Pin Description:
 +
* '''GPIO Pin Description'''
 +
{| class="wikitable"
 +
|-
 +
|Pin# || Name || Linux gpio ||Pin#  || Name || Linux gpio     
 +
|-
 +
|1    || SYS_3.3V  ||    ||2    || VDD_5V ||
 +
|-
 +
|3    || I2C0_SDA  ||    ||4    || VDD_5V ||
 +
|-
 +
|5    || I2C0_SCL  ||    ||6    || GND    ||
 +
|-
 +
|7    || GPIOG11    || 203 ||8    || UART1_TX/GPIOG6 || 198
 +
|-
 +
|9    || GND        ||    ||10    || UART1_RX/GPIOG7 || 199 
 +
|-
 +
|11  || UART2_TX/GPIOA0  || 0      ||12    || PWM1/GPIOA6 || 6
 +
|-
 +
|13  || UART2_RTS/GPIOA2 || 2      ||14    || GND ||
 +
|-
 +
|15  || UART2_CTS/GPIOA3 || 3      ||16    || UART1_RTS/GPIOG8 || 200
 +
|-
 +
|17  || SYS_3.3V        ||        ||18    || UART1_CTS/GPIOG9 || 201
 +
|-
 +
|19  || SPI0_MOSI/GPIOC0 || 64    ||20    || GND              ||
 +
|-
 +
|21  || SPI0_MISO/GPIOC1 || 65    ||22    || UART2_RX/GPIOA1  || 1
 +
|-
 +
|23  || SPI0_CLK/GPIOC2 || 93    ||24    || SPI0_CS/GPIOC3  || 67
 +
|}
 +
 +
* '''USB/Audio/IR Pin Description'''
 +
{| class="wikitable"
 +
|-
 +
|  style="background: PaleTurquoise; color: black" colspan="3"| '''NanoPi-NEO V1.1'''
 +
|-
 +
|Pin# || Name    ||    Description   
 +
|-
 +
|1    || VDD_5V  ||    5V Power Out
 +
|-
 +
|2    || USB-DP1  ||    USB1 DP Signal
 +
|-
 +
|3    || USB-DM1  ||    USB1 DM Signal
 +
|-
 +
|4    || USB-DP2  ||    USB2 DP Signal
 +
|-
 +
|5    || USB-DM2  ||    USB2 DM Signal
 +
|-
 +
|6    || GPIOL11/IR-RX  || GPIOL11 or IR Receive
 +
|-
 +
|7    || SPDIF-OUT/GPIOA17  || GPIOA17 or SPDIF-OUT
 +
|-
 +
|8  || PCM0_SYNC/I2S0_LRC  || I2S/PCM Sample Rate Clock/Sync
 +
|-
 +
|9  || PCM0_CLK/I2S0_BCK  || I2S/PCM Sample Rate Clock
 +
|-
 +
|10  || PCM0_DOUT/I2S0_SDOUT || I2S/PCM Serial Bata Output
 +
|-
 +
|11  || PCM0_DIN/I2S0_SDIN || I2S/PCM Serial Data Input
 +
|-
 +
|12    || GND      || 0V
 +
|}
 +
 +
==Device Operation==
 +
*The Power Dock for NanoPi NEO uses TI's TPS54331 device. The TPS54331 device is a 28-V, 3-A non-synchronous buck converter that integrates a low RDS(on) high-side MOSFET.
 +
 +
==Hardware Setup==
 +
===Connect Power Dock to NanoPi NEO===
 +
A NanoPi NEO can be stacked on the board at side A's female connector. Its side B populates NEO's GPIO pins.<br>
 +
 +
Hardware Setup<br>
 +
[[File:Power Dock for NanoPi NEO_nanopi_NEO.jpg|frameless|500px|Power Dock for NanoPi NEO_nanopi_NEO]]<br>
 +
Connect Power Dock to NanoPi BAT & Other Modules:<br>
 +
[[File:Power Dock for NanoPi NEO_nanopi_NEO0.jpg|frameless|400px|Power Dock for NanoPi BAT]]
 +
[[File:Power Dock for NanoPi NEO_nanopi_NEO1.jpg|frameless|400px|Power Dock for NanoPi NEO Hub]]
 +
[[File:Power Dock for NanoPi NEO_nanopi_NEO2.jpg|frameless|400px|Power Dock for NanoPi RTC]]
 +
[[File:Power Dock for NanoPi NEO_nanopi_NEO3.jpg|frameless|400px|Power Dock for NanoPi GPS]]
 +
 +
==Resources==
 +
 +
==Update Log==
 +
===April-19-2017===
 +
* Released English version

Latest revision as of 09:44, 19 April 2017

查看中文

1 Introduction

Power Dock for NanoPi NEO
  • The Power Dock for NanoPi NEO is a power conversion board.
  • It uses TI's TPS54331 device with wide voltage range.TPS54331 integrates a low RDS(on) high-side MOSFET.
  • Its slow-start feature limits inrush currents. Its overvoltage transient protection circuit limits voltage overshoots during startup and transient conditions.
  • Its side A has double-layer tall female connectors which allow a NEO to be stacked on the board. Its side B populates NEO's GPIO pins.

2 Hardware Spec

  • Input Voltage: 12V
  • Output: 5V/2A
  • Switching Frequency: 570KHz
  • Shutdown Quiescent Current: 1uA
  • Under Voltage Lockout
  • Overvoltage Protection
  • Slow-Start
  • PCB dimension(mm): 40 x 88

Power Dock for NanoPi NEO_PCB

  • Pin Description:
  • GPIO Pin Description
Pin# Name Linux gpio Pin# Name Linux gpio
1 SYS_3.3V 2 VDD_5V
3 I2C0_SDA 4 VDD_5V
5 I2C0_SCL 6 GND
7 GPIOG11 203 8 UART1_TX/GPIOG6 198
9 GND 10 UART1_RX/GPIOG7 199
11 UART2_TX/GPIOA0 0 12 PWM1/GPIOA6 6
13 UART2_RTS/GPIOA2 2 14 GND
15 UART2_CTS/GPIOA3 3 16 UART1_RTS/GPIOG8 200
17 SYS_3.3V 18 UART1_CTS/GPIOG9 201
19 SPI0_MOSI/GPIOC0 64 20 GND
21 SPI0_MISO/GPIOC1 65 22 UART2_RX/GPIOA1 1
23 SPI0_CLK/GPIOC2 93 24 SPI0_CS/GPIOC3 67
  • USB/Audio/IR Pin Description
NanoPi-NEO V1.1
Pin# Name Description
1 VDD_5V 5V Power Out
2 USB-DP1 USB1 DP Signal
3 USB-DM1 USB1 DM Signal
4 USB-DP2 USB2 DP Signal
5 USB-DM2 USB2 DM Signal
6 GPIOL11/IR-RX GPIOL11 or IR Receive
7 SPDIF-OUT/GPIOA17 GPIOA17 or SPDIF-OUT
8 PCM0_SYNC/I2S0_LRC I2S/PCM Sample Rate Clock/Sync
9 PCM0_CLK/I2S0_BCK I2S/PCM Sample Rate Clock
10 PCM0_DOUT/I2S0_SDOUT I2S/PCM Serial Bata Output
11 PCM0_DIN/I2S0_SDIN I2S/PCM Serial Data Input
12 GND 0V

3 Device Operation

  • The Power Dock for NanoPi NEO uses TI's TPS54331 device. The TPS54331 device is a 28-V, 3-A non-synchronous buck converter that integrates a low RDS(on) high-side MOSFET.

4 Hardware Setup

4.1 Connect Power Dock to NanoPi NEO

A NanoPi NEO can be stacked on the board at side A's female connector. Its side B populates NEO's GPIO pins.

Hardware Setup
Power Dock for NanoPi NEO_nanopi_NEO
Connect Power Dock to NanoPi BAT & Other Modules:
Power Dock for NanoPi BAT Power Dock for NanoPi NEO Hub Power Dock for NanoPi RTC Power Dock for NanoPi GPS

5 Resources

6 Update Log

6.1 April-19-2017

  • Released English version
Retrieved from "https://wiki.friendlyelec.com/wiki/index.php?title=Power_Dock_for_NanoPi_NEO&oldid=10122"