Difference between revisions of "NanoPC-T4"

Revision as of 07:44, 21 May 2018

查看中文

1 Introduction

Overview

Front

Back

2 Hardware Spec

• SoC: Rockchip RK3399
  • CPU: big.LITTLE，Dual-Core Cortex-A72(up to 2.0GHz) + Quad-Core Cortex-A53(up to 1.5GHz)
  • GPU: Mali-T864 GPU，supports OpenGL ES1.1/2.0/3.0/3.1, OpenVG1.1, OpenCL, DX11, and AFBC
  • VPU: 4K VP9 and 4K 10bits H265/H264 60fps decoding, Dual VOP, etc
• PMU: RK808-D PMIC, cooperated with independent DC/DC, enabling DVFS, solfware power-down, RTC wake-up, system sleep mode
• RAM: Dual-Channel 4GB LPDDR3
• Flash: 16GB eMMC 5.1 Flash
• Ethernet: Native Gigabit Ethernet
• Wi-Fi/BT: 802.11a/b/g/n/ac, Bluetooth 4.1, Wi-Fi and Bluetooth combo module, dual antenna interface
• Video Input: two 4-Lane MIPI-CSI, dual ISP, up to 13MPix/s，supports simultaneous input of dual camera data
• Video output
  • HDMI: HDMI 2.0a, supports 4K@60Hz，HDCP 1.4/2.2
  • DP on Type-C: DisplayPort 1.2 Alt Mode on USB Type-C
  • LCD Interface: one eDP 1.3（4 lane，10.8Gbps）, one 4-Lane MIPI-DSI
• Audio Out: 3.5mm Dual channel headphone jack, or HDMI
• Audio In: Onboard microphone
• USB 2.0: 2 independent native USB 2.0 Host A interfaces
• USB 3.0: 1 native USB 3.0 Host A type interface
• USB Type-C: Supports USB3.0 Type-C and DisplayPort 1.2 Alt Mode on USB Type-C
• PCIe: One M.2 M-Key PCIe x4 socket, compatible with PCIe 2.1, Dual operation mode; Onboard M3 PCB nut for mounting M.2 2280 module
• microSD Slot x 1
• 40Pin GPIO Extension ports:
  • 1 X 3V/1.8V I2C, up to 2 x 3V UART, 1 X 3V SPI, 1 x SPDIF_TX, up to 8 x 3V GPIOs
  • 1 x 1.8V I2S, 3 x 1.8V GPIOs
• ADC: 3 x 1.8V ADC inputs, 5 Pin 2.54mm header
• Debug: one Debug UART, 4 Pin 2.54mm header, 3V level, 1500000bps
• Keys: PowerKey, Reset, MASKROM(BOOT), Recovery
• LED: 1 x power LED and 1 x GPIO Controled LED
• IR reciver: Onboard IR reciver, Acceptes 38KHz carrier frequency
• RTC Battery: 2 Pin 1.27/1.25mm RTC battery input connector
• Cooling: two 2.5mm PCB nuts for mounting heat sink; 3 Pin 12V cooling fan interface with PWM
• Power supply: DC 12V/2A
• PCB: Ten Layer, 100 mm x 64 mm
• Ambient Operating Temperature: 0℃ to 80℃

3 Software Features

4 Diagram, Layout and Dimension

4.1 Layout

• 40 Pin GPIO Pin Spec

Pin#	Assignment	Pin#	Assignment
1	VCC3V3_SYS	2	VCC5V0_SYS
3	I2C2_SDA(3V)	4	VCC5V0_SYS
5	I2C2_SCL(3V)	6	GND
7	GPIO1_A0(3V)	8	UART2B_TX(3V)
9	GND	10	UART2B_RX(3V)
11	GPIO1_A1(3V)	12	GPIO1_C2(3V)
13	GPIO1_A3(3V)	14	GND
15	GPIO1_A4(3V)	16	GPIO1_C6(3V)
17	VCC3V3_SYS	18	GPIO1_C7(3V)
19	SPI1_TXD/UART4_TX(3V)	20	GND
21	SPI1_RXD/UART4_RX(3V)	22	GPIO1_D0(3V)
23	SPI1_CLK(3V)	24	SPI1_CSn0(3V)
25	GND	26	GPIO4_C5/SPDIF_TX(3V)
27	I2C2_SDA(1.8V)	28	I2C2_SCL(1.8V)
29	I2S1_LRCK_RX(1.8V)	30	GND
31	I2S1_LRCK_TX(1.8V)	32	I2S_CLK(1.8V)
33	I2S1_SCLK(1.8V)	34	GND
35	I2S1_SDI0(1.8V)	36	I2S1_SDO0(1.8V)
37	GPIO3_D4(1.8V)	38	GPIO3_D5(1.8V)
39	GND	40	GPIO3_D6(1.8V)

• eDP Interface Pin Spec

Connector P/N: I-PEX-20455-030E

Pin#	Assignment	Description
1	GND	Signal ground
2	EDP_TX3N	eDP data lane 3 negative output
3	EDP_TX3P	eDP data lane 3 positive output
4	GND	Signal ground
5	EDP_TX2N	eDP data lane 2 negative output
6	EDP_TX2P	eDP data lane 2 positive output
7	GND	Signal ground
8	EDP_TX1N	eDP data lane 1 negative output
9	EDP_TX1P	eDP data lane 1 positive output
10	GND	Signal ground
11	EDP_TX0N	eDP data lane 0 negative output
12	EDP_TX0P	eDP data lane 0 positive output
13	GND	Signal ground
14	EDPAUXP	eDP CH-AUX positive differential output
15	EDPAUXN	eDP CH-AUX negative differential output
16	GND	Signal ground
17	VCC3V3_SYS	3.3V Power output for logic
18	VCC3V3_SYS	3.3V Power output for logic
19	I2C4_SDA	3V I2C data signal, Connect to touch panel
20	I2C4_SCL	3V I2C clock signal, Connect to touch panel
21	GPIO1_C4_TP_INT	3V interrupt input, Connect to the interrupt output of touch panel
22	GPIO1_B5_TP_RST	3V output for reseting touch panel, Connect to the reset input of touch panel
23	PWM0_BL	3V PWM output, for LCD backlight dimming
24	GPIO4_D5_LCD_BL_EN	3V output for turning on/off the LCD backlight
25	GND	Backlight ground
26	GND	Backlight ground
27	GND	Backlight ground
28	VCC12V0_SYS	12V Power output for Backlight Power
29	VCC12V0_SYS	12V Power output for Backlight Power
30	VCC12V0_SYS	12V Power output for Backlight Power

• MIPI-DSI Interface Pin Spec

0.5mm FPC connector

Pin#	Assignment	Description
1, 2, 3	VCC5V0_SYS	5V power output
4	GND	ground
5	I2C4_SDA	3V I2C data signal, Connect to touch panel
6	I2C4_SCL	3V I2C clock signal, Connect to touch panel
7	GND	ground
8	GPIO1_C4_TP_INT	3V interrupt input, Connect to the interrupt output of touch panel
9	GND	ground
10	PWM0_BL	3V PWM output, for LCD backlight dimming
11	GND	ground
12	GPIO4_D5_LCD_BL_EN	3V output for turning on/off the LCD backlight
13	GPIO4_D6_LCD_RST_H	3V output for reseting the LCD module
14	GPIO1_B5_TP_RST	3V output for reseting touch panel, Connect to the reset input of touch panel
15	GND	ground
16	MIPI_TX0_D3N
17	MIPI_TX0_D3P
18	GND
19	MIPI_TX0_D2N
20	MIPI_TX0_D2P
21	GND
22	MIPI_TX0_D1N
23	MIPI_TX0_D1P
24	GND
25	MIPI_TX0_D0N
26	MIPI_TX0_D0P
27	GND
28	MIPI_TX0_CLKN
29	MIPI_TX0_CLKP
30	GND

• MIPI-CSI Interface Pin Spec

0.5mm FPC Connector

Pin#	MIPI-CSI1	MIPI-CSI2	Description
1	VCC5V0_SYS	VCC5V0_SYS	5V Power ouput
2	VCC5V0_SYS	VCC5V0_SYS	5V Power ouput
3	GND	GND	groud
4	VCC_CSI_AF2.8V	VCC_CSI_AF2.8V	2.8V Power for VCM
5	VCC_CSI_1.2V	VCC_CSI_1.2V	1.2V Power for image sensor core circuit
6	VCC1V8_CAM	VCC1V8_CAM	1.8V power for I/O circuit
7	VCC_CSI_2.8V	VCC_CSI_2.8V	2.8V power for image sensor analog circuit
8	VCC_CSI_1.0V	VCC_CSI_1.0V	1.0V Power for image sensor core circuit
9	I2C1_SCL	I2C2_SCL	1.8V I2C clock signal
10	I2C1_SDA	I2C2_SDA	1.8V I2C data signal
11	MIPI_CSI0_RST	MIPI_CSI1_RST	reset camera module
12	MIPI_CSI0_PWN	MIPI_CSI1_PWN	Power down camera module
13	GND	GND	groud
14	GPIO2_B3_CIF_CLKOUTA	GPIO2_B3_CIF_CLKOUTA	MCLK to camera module
15	GND	GND	groud
16	MIPI_RX0_D3P	MIPI_TX1/RX1_D3P	MIPI CSI positive differential data line transceiver output
17	MIPI_RX0_D3N	MIPI_TX1/RX1_D3N	MIPI CSI negative differential data line transceiver output
18	GND	GND	groud
19	MIPI_RX0_D2P	MIPI_TX1/RX1_D2P	MIPI CSI positive differential data line transceiver output
20	MIPI_RX0_D2N	MIPI_TX1/RX1_D2N	MIPI CSI negative differential data line transceiver output
21	GND	GND	groud
22	MIPI_RX0_D1P	MIPI_TX1/RX1_D1P	MIPI CSI positive differential data line transceiver output
23	MIPI_RX0_D1N	MIPI_TX1/RX1_D1N	MIPI CSI negative differential data line transceiver output
24	GND	GND	groud
25	MIPI_RX0_CLKP	MIPI_TX1/RX1_CLKP	MIPI CSI positive differential clock line transceiver output
26	MIPI_RX0_CLKN	MIPI_TX1/RX1_CLKN	MIPI CSI negative differential clock line transceiver output
27	GND	GND	groud
28	MIPI_RX0_D0P	MIPI_TX1/RX1_D0P	MIPI CSI positive differential data line transceiver output
29	MIPI_RX0_D0N	MIPI_TX1/RX1_D0N	MIPI CSI negative differential data line transceiver output
30	GND	GND	groud

Notes

VCC5V0_SYS: 5V Output

VCC3V3_SYS: 3.3V Output

1. For more details refer to the document:

4.2 Board Dimension

NanoPC-T3 Dimensions

For more details refer to the document:

• Power Jack

5 Notes in Hardware Design