Difference between revisions of "NanoPC-T4"

From FriendlyELEC WiKi
Jump to: navigation, search
(Layout)
(Layout)
Line 93: Line 93:
  
 
* '''eDP Interface Pin Spec'''
 
* '''eDP Interface Pin Spec'''
 +
:: Connector P/N: I-PEX-20455-030E
 
::{| class="wikitable"
 
::{| class="wikitable"
 
|-
 
|-
|Pin# || Name         ||Pin# || Name   
+
|Pin# || Name       || Description   
 
+
|-
 +
|1    || GND        || Signal ground
 +
|-
 +
|2    || EDP_TX3N  || eDP data lane 3 negative output
 +
|-
 +
|3    || EDP_TX3P  || eDP data lane 3 positive output 
 +
|-
 +
|4    || GND        || Signal ground
 +
|-
 +
|5    || EDP_TX2N  || eDP data lane 2 negative output
 +
|-
 +
|6    || EDP_TX2P  || eDP data lane 2 positive output     
 +
|-
 +
|7    || GND        || Signal ground
 +
|-
 +
|8    || EDP_TX1N  || eDP data lane 1 negative output 
 +
|-
 +
|9    || EDP_TX1P  || eDP data lane 1 positive output     
 +
|-
 +
|10    || GND      || Signal ground
 +
|-
 +
|11    || EDP_TX0N || eDP data lane 0 negative output 
 +
|-
 +
|12    || EDP_TX0P  || eDP data lane 0 positive output 
 +
|-
 +
|13    || GND      || Signal ground
 +
|-
 +
|14    || EDPAUXP  || eDP CH-AUX positive differential output
 +
|-
 +
|15    || EDPAUXN  || eDP CH-AUX negative differential output 
 +
|-
 +
|16    || GND      || Signal ground
 +
|-
 +
|17    || VCC3V3_SYS || 3.3V Power output for logic
 +
|-
 +
|18    || VCC3V3_SYS || 3.3V Power output for logic
 +
|-
 +
|19    || I2C4_SDA  || I2C4 data signal , 3V level, Connect to touch panel
 +
|-
 +
|20    || I2C4_SCL  || I2C4 clock signal , 3V level, Connect to touch panel
 +
|-
 +
|21    || GPIO1_C4_TP_INT || interrupt input, 3V level, Connect to the interrupt output of touch panel
 +
|-
 +
|22    || GPIO1_B5_TP_RST || for reseting touch panel, 3V level, Connect to the reset input of touch panel 
 +
|-
 +
|23    || PWM0_BL        || PWM0 output, 3V level, for LCD backlight dimming 
 +
|-
 +
|24    || GPIO4_D5_LCD_BL_EN || output, 3V level, for turning on/off the LCD backlight
 +
|-
 +
|25    || GND        || Backlight ground
 +
|-
 +
|26    || GND        || Backlight ground
 +
|-
 +
|27    || GND        || Backlight ground
 +
|-
 +
|28    || VCC12V0_SYS || 12V Power output for Backlight Power
 +
|-
 +
|29    || VCC12V0_SYS || 12V Power output for Backlight Power
 +
|-
 +
|30    || VCC12V0_SYS || 12V Power output for Backlight Power 
 
|}
 
|}
  

Revision as of 06:38, 21 May 2018

查看中文

1 Introduction

Overview
Front
Back

2 Hardware Spec

  • SoC: Rockchip RK3399
    • CPU: big.LITTLE,Dual-Core Cortex-A72(up to 2.0GHz) + Quad-Core Cortex-A53(up to 1.5GHz)
    • GPU: Mali-T864 GPU,supports OpenGL ES1.1/2.0/3.0/3.1, OpenVG1.1, OpenCL, DX11, and AFBC
    • VPU: 4K VP9 and 4K 10bits H265/H264 60fps decoding, Dual VOP, etc
  • PMU: RK808-D PMIC, cooperated with independent DC/DC, enabling DVFS, solfware power-down, RTC wake-up, system sleep mode
  • RAM: Dual-Channel 4GB LPDDR3
  • Flash: 16GB eMMC 5.1 Flash
  • Ethernet: Native Gigabit Ethernet
  • Wi-Fi/BT: 802.11a/b/g/n/ac, Bluetooth 4.1, Wi-Fi and Bluetooth combo module, dual antenna interface
  • Video Input: two 4-Line MIPI-CSI, dual ISP, up to 13MPix/s,supports simultaneous input of dual camera data
  • Video output
    • HDMI: HDMI 2.0a, supports 4K 60Hz,HDCP 1.4/2.2
    • DP on Type-C: DisplayPort 1.2 Alt Mode on USB Type-C
    • LCD Interface: one eDP 1.3(4 line,10.8Gbps), one 4-Line MIPI-DSI
  • Audio Out: 3.5mm Dual channel headphone jack, or HDMI
  • Audio In: Onboard microphone
  • USB 2.0: 2 independent native USB 2.0 Host A interfaces
  • USB 3.0: 1 native USB 3.0 Host A type interface
  • USB Type-C: Supports USB3.0 Type-C and DisplayPort 1.2 Alt Mode on USB Type-C
  • PCIe: One M.2 M-Key PCIe x4 socket, compatible with PCIe 2.1, Dual operation mode; Onboard M3 PCB nut for mounting M.2 2280 module
  • 40Pin GPIO Extension ports:
    • 1 X 3V/1.8V I2C, up to 2 x 3V UART, 1 X 3V SPI, 1 x SPDIF_TX, up to 8 x 3V GPIOs
    • 1 x 1.8V I2S, 3 x 1.8V GPIOs
  • ADC: 3 x 1.8V ADC inputs, 5 Pin 2.54mm header
  • Debug: one Debug UART, 4 Pin 2.54mm header, 3V level, 1500000bps
  • Keys: PowerKey, Reset, MASKROM(BOOT), Recovery
  • LED: 1 x power LED and 1 x GPIO Controled LED
  • IR reciver: Onboard IR reciver, Acceptes 38KHz carrier frequency
  • RTC Battery: 2 Pin 1.27/1.25mm RTC battery input connector
  • Cooling: two 2.5mm PCB nuts for mounting heat sink; 3 Pin 12V cooling fan interface with PWM
  • Power supply: DC 12V/2A
  • PCB: Ten Layer, 100 mm x 64 mm
  • Ambient Operating Temperature: 0℃ to 80℃

3 Software Features

4 Diagram, Layout and Dimension

4.1 Layout

  • 40 Pin GPIO Pin Spec
Pin# Name Pin# Name
1 VCC3V3_SYS 2 VCC5V0_SYS
3 I2C2_SDA(3V) 4 VCC5V0_SYS
5 I2C2_SCL(3V) 6 GND
7 GPIO1_A0(3V) 8 UART2B_TX(3V)
9 GND 10 UART2B_RX(3V)
11 GPIO1_A1(3V) 12 GPIO1_C2(3V)
13 GPIO1_A3(3V) 14 GND
15 GPIO1_A4(3V) 16 GPIO1_C6(3V)
17 VCC3V3_SYS 18 GPIO1_C7(3V)
19 SPI1_TXD/UART4_TX(3V) 20 GND
21 SPI1_RXD/UART4_RX(3V) 22 GPIO1_D0(3V)
23 SPI1_CLK(3V) 24 SPI1_CSn0(3V)
25 GND 26 GPIO4_C5/SPDIF_TX(3V)
27 I2C2_SDA(1.8V) 28 I2C2_SCL(1.8V)
29 I2S1_LRCK_RX(1.8V) 30 GND
31 I2S1_LRCK_TX(1.8V) 32 I2S_CLK(1.8V)
33 I2S1_SCLK(1.8V) 34 GND
35 I2S1_SDI0(1.8V) 36 I2S1_SDO0(1.8V)
37 GPIO3_D4(1.8V) 38 GPIO3_D5(1.8V)
39 GND 40 GPIO3_D6(1.8V)
  • eDP Interface Pin Spec
Connector P/N: I-PEX-20455-030E
Pin# Name Description
1 GND Signal ground
2 EDP_TX3N eDP data lane 3 negative output
3 EDP_TX3P eDP data lane 3 positive output
4 GND Signal ground
5 EDP_TX2N eDP data lane 2 negative output
6 EDP_TX2P eDP data lane 2 positive output
7 GND Signal ground
8 EDP_TX1N eDP data lane 1 negative output
9 EDP_TX1P eDP data lane 1 positive output
10 GND Signal ground
11 EDP_TX0N eDP data lane 0 negative output
12 EDP_TX0P eDP data lane 0 positive output
13 GND Signal ground
14 EDPAUXP eDP CH-AUX positive differential output
15 EDPAUXN eDP CH-AUX negative differential output
16 GND Signal ground
17 VCC3V3_SYS 3.3V Power output for logic
18 VCC3V3_SYS 3.3V Power output for logic
19 I2C4_SDA I2C4 data signal , 3V level, Connect to touch panel
20 I2C4_SCL I2C4 clock signal , 3V level, Connect to touch panel
21 GPIO1_C4_TP_INT interrupt input, 3V level, Connect to the interrupt output of touch panel
22 GPIO1_B5_TP_RST for reseting touch panel, 3V level, Connect to the reset input of touch panel
23 PWM0_BL PWM0 output, 3V level, for LCD backlight dimming
24 GPIO4_D5_LCD_BL_EN output, 3V level, for turning on/off the LCD backlight
25 GND Backlight ground
26 GND Backlight ground
27 GND Backlight ground
28 VCC12V0_SYS 12V Power output for Backlight Power
29 VCC12V0_SYS 12V Power output for Backlight Power
30 VCC12V0_SYS 12V Power output for Backlight Power
  • MIPI-CSI Interface Pin Spec
Pin# MIPI-CSI2
  • MIPI-DSI Interface Pin Spec
Pin# Name


Notes
VCC5V0_SYS: 5V Output
VCC3V3_SYS: 3.3V Output
  1. For more details refer to the document:

4.2 Board Dimension

NanoPC-T3 Dimensions

For more details refer to the document:
  • Power Jack

5 Notes in Hardware Design