Difference between revisions of "Matrix - Thermistor"

From FriendlyELEC WiKi
Jump to: navigation, search
(介绍)
(Code Sample)
 
(18 intermediate revisions by 3 users not shown)
Line 1: Line 1:
[[Matrix - Thermistor |English]]
+
[[Matrix - Thermistor/zh|查看中文]]
  
==介绍==
+
==Introduction==
 
[[File:Thermistor.png|thumb|Thermistor]]
 
[[File:Thermistor.png|thumb|Thermistor]]
*Matrix-Thermistor是一个模拟热敏电阻模块。3-Pin 2.54mm排针,V接电源,G接地,S信号输出模拟电压信号。您可以把S输出的电压信号通过ADC转换成数字信号,得到与北侧物体温度对应的电压值。
+
*The Matrix-Thermistor module is a thermistor module. It has a 3 pin 2.54mm spacing pin header of which V is supply voltage, G is ground and S is output analog signal. Users can convert output analog signals to digital signals via ADC conversion.
*为提高测试的准确度,请把传感器与被测物体直接紧密接触。
+
*To increase measured values' accuracy please make the sensor in close contact with a measured object.
  
==特性==
+
==Features==
* GPIO,3.3/5V电平
+
* GPIO, 3.3/5V
* 体积小巧
+
* Small
* 2.54mm排针接口
+
* 2.54mm spacing pin header
* PCB尺寸(mm):8x24
+
* PCB Dimension(mm): 8 x 24
[[File:xxx.png | frameless|400px|xxx.PCB]]
+
[[File:Thermistor01.png | frameless|400px|Thermistor01.PCB]]
  
* 引脚说明:
+
* Pin Description:
 
{| class="wikitable"
 
{| class="wikitable"
 
|-
 
|-
|名称 || 描述
+
|Pin || Description
 
|-
 
|-
|S    || 模拟GPIO
+
|S    || Analog GPIO
 
|-
 
|-
|V    || 电源5V
+
|V    || Supply Voltage 5V
 
|-
 
|-
|G    ||
+
|G    || Ground
 
|}
 
|}
  
==工作原理==
+
==Basic Device Operation==
*模块主要器件是一个热电阻温度传感器,热电阻的测温原理是基于导体或半导体的电阻值随着温度的变化而变化的特性,在电源激励下,输出端的分压也随之变化。
+
* The module mainly contains a thermistor. A thermistor is a type of resistor whose resistance is dependent on temperature.
  
==下载Matrix源码==
+
==Applications==
 +
The Matrix-Thermistor module outputs analog signals which can be converted to digital signals through an ADC converter e.g. the Matrix-Analog_to_Digital_Converter module.<br>
 +
For more details about the Matrix-Analog_to_Digital_Converter module refer to wiki:[[Matrix_-_Analog_to_Digital_Converter]].<br>
 +
 
 +
===Connect to NanoPi M1===
 +
Refer to the following connection diagram to connect the module to the NanoPi M1:<br>
 +
[[File:Matrix-Thermistor_nanopi_m1.jpg|frameless|600px|Matrix-Thermistor_nanopi_m1]]
 +
 
 +
Connection Details:
 +
{| class="wikitable"
 +
|-
 +
|Matrix-Thermistor ||     
 +
|-
 +
|GND    || NanoPi M1 Pin9
 +
|-
 +
|5V    || NanoPi M1 Pin2
 +
|-
 +
|S      || Matrix-Analog_to_Digital_Converter A0
 +
|}
 +
 
 +
===Connect to NanoPi 2===
 +
Refer to the following connection diagram to connect the module to the NanoPi 2:<br>
 +
[[File:Matrix-Thermistor_nanopi_2.jpg|frameless|600px|Matrix-Thermistor_nanopi_2]]
 +
 
 +
Connection Details:
 +
{| class="wikitable"
 +
|-
 +
|Matrix-Thermistor ||     
 +
|-
 +
|GND    || NanoPi 2 Pin9
 +
|-
 +
|5V    || NanoPi 2 Pin2
 +
|-
 +
|S      || Matrix-Analog_to_Digital_Converter A0
 +
|}
 +
 
 +
===Connect to NanoPi M2 / NanoPi 2 Fire===
 +
Refer to the following connection diagram to connect the module to the NanoPi M2/ NanoPi 2 Fire:<br>
 +
[[File:Matrix-Thermistor_nanopi_m2.jpg|frameless|600px|Matrix-Thermistor_nanopi_m2]]
 +
 
 +
Connection Details:
 +
{| class="wikitable"
 +
|-
 +
|Matrix-Thermistor ||     
 +
|-
 +
|GND    || NanoPi M2 Pin9
 +
|-
 +
|5V    || NanoPi M2 Pin2
 +
|-
 +
|S      || Matrix-Analog_to_Digital_Converter A0
 +
|}
 +
 
 +
===Connect to NanoPC-T2===
 +
Refer to the following connection diagram to connect the module to the NanoPC-T2:<br>
 +
[[File:Matrix-Thermistor_NanoPC-T2.jpg|frameless|600px|Matrix-Thermistor_NanoPC-T2]]
 +
 
 +
Connection Details:
 +
{| class="wikitable"
 +
|-
 +
|Matrix-Potentiometer ||     
 +
|-
 +
|GND    || NanoPC-T2 USB Host GND
 +
|-
 +
|5V    || NanoPC-T2 USB Host 5V
 +
|-
 +
|S      || Matrix-Analog_to_Digital_Converter A0
 +
|}
 +
 
 +
==Compile & Run Test Program==
 +
Boot your ARM board with Debian and copy the matrix code:
 +
<syntaxhighlight lang="bash">
 +
$ apt-get update && apt-get install git
 +
$ git clone https://github.com/friendlyarm/matrix.git
 +
</syntaxhighlight>
 +
If your cloning is done successfully a "matrix" directory will be generated.
 +
 
 +
Compile and install Matrix:
 +
<syntaxhighlight lang="bash">
 +
$ cd matrix
 +
$ make && make install
 +
</syntaxhighlight>
 +
 
 +
Run test program:
 +
<syntaxhighlight lang="bash">
 +
$ matrix-adc
 +
</syntaxhighlight>
 +
Note: this module is not plug and play therefore before running the module please make sure it is connected to an ARM board.<br>
 +
Here is what you should observe:<br>
 +
<syntaxhighlight lang="bash">
 +
The channel0 value is 2460
 +
</syntaxhighlight>
 +
 
 +
==Code Sample==
 +
This Matrix code sample can work with all the ARM boards mentioned in this module's wiki. The name of this code sample is "matrix-analog_to_digital_converter". Here is its source code:
 +
<syntaxhighlight lang="c">
 +
int main(int argc, char ** argv)
 +
{
 +
    int i = 0;
 +
    int value = 0;
 +
    int channel = 0;
 +
 
 +
    if (boardInit() < 0) {
 +
        printf("Fail to init board\n");
 +
        return -1;
 +
    }
 +
   
 +
    if (argc == 2)
 +
        channel = atoi(argv[1]);
 +
    system("modprobe "DRIVER_MODULE);
 +
    signal(SIGINT, intHandler);
 +
    for (i=0; i<ADC_READ_TIMES; i++) {
 +
        if (pcf8591Read(channel, &value) != -1) {
 +
            printf("The channel%d value is %d\n", channel, value);
 +
        } else {
 +
            printf("Fail to get channel%d value\n", channel);
 +
        }
 +
    }
 +
    system("rmmod "DRIVER_MODULE);
 +
   
 +
    return 0;
 +
}
 +
</syntaxhighlight>
 +
For more details about this APIs called in this code sample refer to [[Matrix API reference manual]] <br>
 +
 
 +
==Resources==
 +
 
 +
==Update Log==
 +
===June-25-2016===
 +
* Re-organized and simplified wiki
 +
 
 +
 
 +
<!---
 +
==Download Matrix Source Code==
 +
All the matrix modules' code samples are open source. They are maintained on GitHub: https://github.com/friendlyarm/matrix.git <br>
 +
Each branch in this hub contains the matrix modules' code samples for a board that the matrix modules can work with.<br>
 +
* The matrix-nanopi branch contains the matrix modules' code samples for the NanoPi;
 +
* The matrix-nanopi2 branch contains the matrix modules' code samples for the NanoPi 2;
 +
* The matrix-tiny4412 branch contains the matrix modules' code samples for the Tiny4412;
 +
* The matrix-raspberrypi branch contains the matrix modules' code samples for the RaspberryPi;
 +
 
 +
Please follow the steps below to get the source code:<br>
 +
Install the git utility on a PC running Ubuntu14.04<br>
 +
<syntaxhighlight lang="bash">
 +
$ sudo apt-get install git
 +
</syntaxhighlight>
 +
 
 +
Clone the matrix code from GitHub
 +
<syntaxhighlight lang="bash">
 +
$ git clone https://github.com/friendlyarm/matrix.git
 +
</syntaxhighlight>
 +
If this is successful a "matrix" directory will be generated, which will contain all the matrix modules' code samples
 +
 
 +
==Connect to NanoPi 2==
 +
===Hardware Connection===
 +
Please refer to the following connection diagram to connect the Matrix-Thermistor to the NanoPi 2:<br>
 +
[[File:Matrix-Thermistor.jpg|frameless|600px|Matrix-Thermistor]]
 +
 
 +
Connection Details:
 +
{| class="wikitable"
 +
|-
 +
|Matrix-Analog_to_Digital_Converter || NanoPi 2     
 +
|-
 +
|SDA    || Pin3
 +
|-
 +
|SCL    || Pin5
 +
|-
 +
|5V    || Pin4
 +
|-
 +
|GND    || Pin6
 +
|}
 +
 
 +
{| class="wikitable"
 +
|-
 +
|Matrix-Thermistor ||     
 +
|-
 +
|GND    || NanoPi 2 Pin9
 +
|-
 +
|5V    || NanoPi 2 Pin2
 +
|-
 +
|S      || Matrix-Analog_to_Digital_Converter A0
 +
|}
 +
This module's output signals are analog signals. You can use our Matrix-Analog_to_Digital_Converter to convert them to digital signals.<br>
 +
Please connect the Matrix-Analog_to_Digital_Converter to the NanoPi 2 and then connect Pin S of the Matrix-Thermistor's pin header to Matrix-Analog_to_Digital_Converter's A0.<br>
 +
For more details about the Matrix-Analog_to_Digital_Converter module please refer to wiki:[[Matrix_-_Analog_to_Digital_Converter]].<br>
 +
 
 +
===Compile Test Program===
 +
Please login the matrix hub and enter the nanopi2 branch
 +
<syntaxhighlight lang="bash">
 +
$ cd matrix
 +
$ git checkout nanopi2
 +
</syntaxhighlight>
 +
 
 +
Compile the Matrix code
 +
<syntaxhighlight lang="bash">
 +
$ make CROSS_COMPILE=arm-linux- clean
 +
$ make CROSS_COMPILE=arm-linux-
 +
$ make CROSS_COMPILE=arm-linux- install
 +
</syntaxhighlight>
 +
Note: please make sure to install the cross compiler "arm-linux-gcc-4.9.3" on your PC, which is used to compile files for the NanoPi 2.<br>
 +
Generated library files are under the "install/lib" directory. The test program is under the "install/usr/bin" directory. Its test program is "matrix-adc".<br>
 +
The modules are under the "modules" directory. Its driver's source code is in https://github.com/friendlyarm/linux-3.4.y.git.<br>
 +
 
 +
===Run Test Program===
 +
Please insert a TF card which is flashed with Debian to a Linux host and mount its boot and rootfs sections.<br>
 +
We assume the rootfs is mounted to /media/rootfs then please run the following commands to copy the driver, library and test program to the card.<br>
 +
<syntaxhighlight lang="bash">
 +
$ cp modules /media/rootfs/ -r
 +
$ cp install/lib/* /media/rootfs/lib/ -d
 +
$ cp install/usr/bin/* /media/rootfs/usr/bin/
 +
</syntaxhighlight>
 +
 
 +
Insert this TF card to your NanoPi 2, power on and run the following commands to load the driver.<br>
 +
<syntaxhighlight lang="bash">
 +
$ cd /modules
 +
$ insmod pcf8591.ko
 +
</syntaxhighlight>
 +
 
 +
Please run the following command to test the Matrix-Thermistor module.<br>
 +
<syntaxhighlight lang="bash">
 +
$ matrix-adc
 +
</syntaxhighlight>
 +
Here is what you should expect:<br>
 +
[[File:matrix-adc_result.png|frameless||matrix-adc_result]] <br>
 +
 
 +
===Code Sample===
 +
<syntaxhighlight lang="c">
 +
int main(int argc, char ** argv)
 +
{
 +
    int i = 0;
 +
    int value = 0;
 +
    int channel = 0;
 +
 
 +
    if (argc == 2) {
 +
        channel = atoi(argv[1]);
 +
    }
 +
   
 +
    for (i=0; i<ADC_READ_TIMES; i++) {
 +
        if (pcf8591Read(channel, &value) != -1) {
 +
            printf("channel%d value=%d\n", channel, value);
 +
        } else {
 +
            printf("Fail to get channel%d value\n", channel);       
 +
        }
 +
        usleep(10000);
 +
    }
 +
    return 0;
 +
}
 +
</syntaxhighlight>
 +
--->

Latest revision as of 16:24, 24 June 2016

查看中文

1 Introduction

Thermistor
  • The Matrix-Thermistor module is a thermistor module. It has a 3 pin 2.54mm spacing pin header of which V is supply voltage, G is ground and S is output analog signal. Users can convert output analog signals to digital signals via ADC conversion.
  • To increase measured values' accuracy please make the sensor in close contact with a measured object.

2 Features

  • GPIO, 3.3/5V
  • Small
  • 2.54mm spacing pin header
  • PCB Dimension(mm): 8 x 24

Thermistor01.PCB

  • Pin Description:
Pin Description
S Analog GPIO
V Supply Voltage 5V
G Ground

3 Basic Device Operation

  • The module mainly contains a thermistor. A thermistor is a type of resistor whose resistance is dependent on temperature.

4 Applications

The Matrix-Thermistor module outputs analog signals which can be converted to digital signals through an ADC converter e.g. the Matrix-Analog_to_Digital_Converter module.
For more details about the Matrix-Analog_to_Digital_Converter module refer to wiki:Matrix_-_Analog_to_Digital_Converter.

4.1 Connect to NanoPi M1

Refer to the following connection diagram to connect the module to the NanoPi M1:
Matrix-Thermistor_nanopi_m1

Connection Details:

Matrix-Thermistor
GND NanoPi M1 Pin9
5V NanoPi M1 Pin2
S Matrix-Analog_to_Digital_Converter A0

4.2 Connect to NanoPi 2

Refer to the following connection diagram to connect the module to the NanoPi 2:
Matrix-Thermistor_nanopi_2

Connection Details:

Matrix-Thermistor
GND NanoPi 2 Pin9
5V NanoPi 2 Pin2
S Matrix-Analog_to_Digital_Converter A0

4.3 Connect to NanoPi M2 / NanoPi 2 Fire

Refer to the following connection diagram to connect the module to the NanoPi M2/ NanoPi 2 Fire:
Matrix-Thermistor_nanopi_m2

Connection Details:

Matrix-Thermistor
GND NanoPi M2 Pin9
5V NanoPi M2 Pin2
S Matrix-Analog_to_Digital_Converter A0

4.4 Connect to NanoPC-T2

Refer to the following connection diagram to connect the module to the NanoPC-T2:
Matrix-Thermistor_NanoPC-T2

Connection Details:

Matrix-Potentiometer
GND NanoPC-T2 USB Host GND
5V  NanoPC-T2 USB Host 5V
S Matrix-Analog_to_Digital_Converter A0

5 Compile & Run Test Program

Boot your ARM board with Debian and copy the matrix code:

$ apt-get update && apt-get install git
$ git clone https://github.com/friendlyarm/matrix.git

If your cloning is done successfully a "matrix" directory will be generated.

Compile and install Matrix:

$ cd matrix
$ make && make install

Run test program:

$ matrix-adc

Note: this module is not plug and play therefore before running the module please make sure it is connected to an ARM board.
Here is what you should observe:

The channel0 value is 2460

6 Code Sample

This Matrix code sample can work with all the ARM boards mentioned in this module's wiki. The name of this code sample is "matrix-analog_to_digital_converter". Here is its source code:

int main(int argc, char ** argv)
{
    int i = 0;
    int value = 0;
    int channel = 0;
 
    if (boardInit() < 0) {
        printf("Fail to init board\n");
        return -1;
    }
 
    if (argc == 2)
        channel = atoi(argv[1]);
    system("modprobe "DRIVER_MODULE);
    signal(SIGINT, intHandler);
    for (i=0; i<ADC_READ_TIMES; i++) {
        if (pcf8591Read(channel, &value) != -1) {
            printf("The channel%d value is %d\n", channel, value);
        } else {
            printf("Fail to get channel%d value\n", channel);
        }
    }
    system("rmmod "DRIVER_MODULE);
 
    return 0;
}

For more details about this APIs called in this code sample refer to Matrix API reference manual

7 Resources

8 Update Log

8.1 June-25-2016

  • Re-organized and simplified wiki