Difference between revisions of "Debian Jessie"

From FriendlyELEC WiKi
Jump to: navigation, search
(Login via VNC and SSH)
(Test USB WiFi)
Line 213: Line 213:
 
<br />
 
<br />
 
For more details about NetworkManager refer to this link:[[Use NetworkManager to configure network settings]]<br />
 
For more details about NetworkManager refer to this link:[[Use NetworkManager to configure network settings]]<br />
 +
 +
===Connect to DVP Camera CAM500B (Only Support H3 Platform)===
 +
Note: this function is only supported in Linux-3.4.y<br>
 +
The CAM500B camera module is a 5M-pixel camera with DVP interface. For more tech details about it you can refer to [[Matrix - CAM500B]].<br>
 +
[[File:NanoPi-M1-cam500a.jpg|frameless|500px|NanoPi-M1-cam500a]] <br>
 +
Follow the hardware setup presented in the above picture to connect your H3 board to a CAM500B. Then boot OS, connect your board to a network, log into the board as root and run "mjpg-streamer":
 +
<syntaxhighlight lang="bash">
 +
$ cd /root/mjpg-streamer
 +
$ make
 +
$ ./start.sh
 +
</syntaxhighlight>
 +
The mjpg-streamer application is an open source video steam server. After it is successfully started the following messages will be popped up:
 +
<syntaxhighlight lang="bash">
 +
i: Using V4L2 device.: /dev/video0
 +
i: Desired Resolution: 1280 x 720
 +
i: Frames Per Second.: 30
 +
i: Format............: YUV
 +
i: JPEG Quality......: 90
 +
o: www-folder-path...: ./www/
 +
o: HTTP TCP port.....: 8080
 +
o: username:password.: disabled
 +
o: commands..........: enabled
 +
</syntaxhighlight>
 +
 +
In our case the board's IP address was 192.168.1.230. We typed 192.168.1.230:8080 in a browser and were able to view the images taken from the camera's. Here is what you would expect to observe:<br>
 +
[[File:mjpg-streamer-cam500a.png|frameless|600px|mjpg-streamer-cam500a]] <br>
 +
The mjpg-streamer soft-encodes data with libjpeg and you can hard-encode its data with ffmpeg which will greatly increase CPU's efficiency and speed up data encoding:
 +
<syntaxhighlight lang="bash">
 +
$ ffmpeg -t 30 -f v4l2 -channel 0 -video_size 1280x720 -i /dev/video0 -pix_fmt nv12 -r 30 \
 +
        -b:v 64k -c:v cedrus264 test.mp4
 +
</syntaxhighlight>
 +
By default it records a 30-second video. Typing "q" stops video recording. After recording is stopped a test.mp4 file will be generated.

Revision as of 06:17, 21 December 2017

查看中文

1 Download debian image file

1.1 S5P4418 Boards

Get the following files from:download link,Image filename:

s5p4418-debian-sd8g-20171017.img.zip Debian8-Desktop

1.2 S5P6818 Boards

Get the following files from:download link,Image filename:

s5p6818-debian-sd8g-20171102.img.zip Debian8-Desktop

2 Working with Debian

2.1 Ethernet Connection

  • If the board is connected to a network via Ethernet before it is powered on, it will automatically obtain an IP after it is powered up.

2.2 Wireless Connection

Under Debian you can manage your network with NetworkManager.
After Debian boots click on the network icon on the bottom right of the task bar a NetworkManger menu will pop up and all the available networks will be listed. If there is an active wireless network you will see something similar to the following screenshot:
NetworkManagerIcon
You can click on a WiFI AP and connect your board to it.
For more details refer to:NetworkManager.

2.3 Setup Wi-Fi AP

Follow the steps below. Since our OS image by default already has the NetworkManager utility you will be prompted to uninstall it first:

sudo turn-wifi-into-apmode yes

After you uninstall the NetworkManager reboot your board.
After your board is rebooted run the above commands again and you will be prompted to type in a WIFI's name and password. Type in your wanted name and password

If this is successful you will be able to find and connect your board to a WIFI. Login to your board at 192.168.8.1:

ssh root@192.168.8.1

Type in a password. In our system the password is "fa".

To login smoothly via SSH we recommend you turning off WIFI's power save mode by running the following commands:

sudo iwconfig wlan0 power off

You can check your WiFi's mode by running the following command:

sudo cat /sys/module/bcmdhd/parameters/op_mode

Number 2 means your WiFi is in AP mode. You can switch to the Station mode by running the following command:

sudo turn-wifi-into-apmode no

2.4 Bluetooth

Here are the steps to transfer a file from T2 to a mobile phone. Run the following command to search a surrounding Bluetooth device:

hcitool scan


In our example a mobile phone was detected and the following messages were listed:
Scanning ...
38:BC:1A:B1:7E:DD MEIZU MX4

These messages indicated that a MEIZU MX4 mobile phone was detected. We then checked the Bluetooth services this phone supported with its MAC address presented in front of its device name

sdptool browse 38:BC:1A:B1:7E:DD

Note: you need to use your device's name and its MAC address when you run these commands.

The command listed all the services the phone supported. We needed the "OBEX Object Push" service which is for file transfers.
Service Name: OBEX Object Push
Service RecHandle: 0x1000b
Service Class ID List:
"OBEX Object Push" (0x1105)
Protocol Descriptor List:
"L2CAP" (0x0100)
"RFCOMM" (0x0003)
Channel: 25
"OBEX" (0x0008)
Profile Descriptor List:
"OBEX Object Push" (0x1105)
Version: 0x0100

From the above messages we could get the channel number 25 for the "OBEX Object Push" service. We input this number to the "ussp-push" by running the following command:

ussp-push 38:BC:1A:B1:7E:DD@25 example.jpg example.jpg

Note: you need to use your device's name, its MAC address and channel number when you run these commands.

Usually after the above commands are run a popup window will show on the phone that communicates with T2 and you can start file transfers.

Common Issues:
1) If T2 cannot find a Bluetooth device you can try this command to restart its Bluetooth:

rfkill unblock 0

2) If any of these commands is not installed you can try this command to install it:

apt-get install bluetooth bluez obexftp openobex-apps python-gobject ussp-push

2.5 Install Debian Packages

We provide a Debian Jessie image. You can install Jessie's packages by commanding "apt-get". If this is your first installation you need to update the package list by running the following command

apt-get update

You can install your preferred packages. For example if you want to install an FTP server you can do this:

apt-get install vsftpd

Note: you can change your download server by editting "/etc/apt/sources.list". You can get a complete server list from [1]. You need to select the one with "armhf".

2.6 Audio Output from HDMI or 3.5mm Jack under Debian

Our default Debian image doesn't support audio output. If you want to enable this function you need to install the alsa package.

  •  Make sure your Debian OS is our latest version and your board has access to the internet;
  •  Power up your board and run the following commands on your board's commandline utility to install the alsa package:
apt-get update
apt-get install libasound2
apt-get install alsa-base
apt-get install alsa-utils
  • After the installation is done copy a ".wav" audio file to your board, connect your board to a earphone or speaker and try playing this audio file(By default Debian's audio output is from the 3.5mm audio jack):
aplay music.wav
  • By default Debian's audio output is from the 3.5mm audio jack. If you want audio output from the HDMI you need to change the setting by editing the "/etc/asound.conf" file:
pcm.!default {
    type hw
    card 1
    device 0}
 
ctl.!default {
    type hw
    card 1}

card 0 stands for the 3.5mm audio jack and card 1 stands for the HDMI audio. After you make your change reboot your board to make it effective.


2.7 Login via VNC and SSH

If your board is not connected to a display device you can login to your board from a mobile phone. You need to download and install a "VNC Viewer" from here on a mobile phone and login to the board via VNC at port 1. Its default password is "fa123456".
Here is a screenshot which shows how it looks like when users login to the board from an iPhone via VNC:
VNC to NanoPi2
In our case our M1's IP address is 192.168.1.230. You can login via SSH by running the following commands:

$ ssh root@192.168.1.230

The password is fa.

2.8 Test GPU (Only support H3/H5)

Note: this function is only supported in Allwinner Linux-3.4.y.
After OS loads please login from a terminal and run the following command:

glmark2-es2

m1-gpu-glmark2

2.9 Test VPU (Only support H3/H5)

Note: this function is only supported in Allwinner Linux-3.4.y
Visit this link download link to download files
After OS is loaded login from a terminal and run the following commands:

$ sudo apt-get install mpv
$ video_play mpv ./big_buck_bunny_1080p_H264_AAC_25fps_7200K.MP4

In our test it could do hard coding and play 1080P video fluently.

2.10 Test USB WiFi

Our OS system has support for popular USB WiFi drivers. Many USB WiFi modules are plug and play with our system. Here is a list of models we tested;

Number Model
1 RTL8188CUS 802.11n WLAN Adapter
2 RT2070 Wireless Adapter
3 RT2870/RT3070 Wireless Adapter
4 RTL8192CU Wireless Adapter
5 mi WiFi mt7601
  • Check device list
$ nmcli dev
DEVICE  TYPE      STATE         CONNECTION         
eth0    ethernet  connected     Wired connection 1 
wlan0   wifi      disconnected  --                                  
lo      loopback  unmanaged     --

Note: if the status of a device is "unmanaged" it means that device cannot be accessed by NetworkManager. To make is accessed you need to clear the settings under "/etc/network/interfaces" and reboot your system.

  • Start WiFi
$ nmcli r wifi on
  • Scan Surrounding WiFi Sources
$ nmcli dev wifi
  • Connect to a WiFi Source
$ nmcli dev wifi connect "SSID" password "PASSWORD"

The "SSID" and "PASSWORD" need to be replaced with your actual SSID and password.
If a connection succeeds it will be automatically setup on next system reboot.

For more details about NetworkManager refer to this link:Use NetworkManager to configure network settings

2.11 Connect to DVP Camera CAM500B (Only Support H3 Platform)

Note: this function is only supported in Linux-3.4.y
The CAM500B camera module is a 5M-pixel camera with DVP interface. For more tech details about it you can refer to Matrix - CAM500B.
NanoPi-M1-cam500a
Follow the hardware setup presented in the above picture to connect your H3 board to a CAM500B. Then boot OS, connect your board to a network, log into the board as root and run "mjpg-streamer":

$ cd /root/mjpg-streamer
$ make
$ ./start.sh

The mjpg-streamer application is an open source video steam server. After it is successfully started the following messages will be popped up:

 
 i: Using V4L2 device.: /dev/video0
 i: Desired Resolution: 1280 x 720
 i: Frames Per Second.: 30
 i: Format............: YUV
 i: JPEG Quality......: 90
 o: www-folder-path...: ./www/
 o: HTTP TCP port.....: 8080
 o: username:password.: disabled
 o: commands..........: enabled

In our case the board's IP address was 192.168.1.230. We typed 192.168.1.230:8080 in a browser and were able to view the images taken from the camera's. Here is what you would expect to observe:
mjpg-streamer-cam500a
The mjpg-streamer soft-encodes data with libjpeg and you can hard-encode its data with ffmpeg which will greatly increase CPU's efficiency and speed up data encoding:

$ ffmpeg -t 30 -f v4l2 -channel 0 -video_size 1280x720 -i /dev/video0 -pix_fmt nv12 -r 30 \
        -b:v 64k -c:v cedrus264 test.mp4

By default it records a 30-second video. Typing "q" stops video recording. After recording is stopped a test.mp4 file will be generated.